Page 8 of 23 FirstFirst ... 67891018 ... LastLast
Results 71 to 80 of 222

Thread: Airdrome Aeroplanes Nieuport 17

  1. #71
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    209
    June was a busy month and other than the trip to pick up the cowl, no work on the N17. I have since completed the bracket attachments on the upper wing ribs. I then moved on to forming the lower wing ribs.

    Before starting on the lower ribs, I had to test the fit of my propeller to the engine hub. Nice.

    Name:  m_DSC05138.jpg
Views: 3176
Size:  54.8 KB

    Then on to the lower ribs. Since I changed the profile (thinner) I had to fiddle with the bend of the upper ribs as I could not find a single bend on the fixture that would do what I wanted. A little tweaking of each part was required. But they came out nice.

    Name:  m_DSC05137.jpg
Views: 2844
Size:  79.4 KB

    Then to cut the shape on the nose.

    Name:  m_IMG_20160709_125431_783.jpg
Views: 2863
Size:  46.1 KB

    Name:  m_IMG_20160709_125453_083.jpg
Views: 2797
Size:  72.2 KB

    Name:  m_DSC05143.jpg
Views: 2805
Size:  69.0 KB

    Then I built the fixtures for attaching the brackets that tie the ribs to the spars. At this point I have not cut the tails of the ribs.

    Name:  m_DSC05146.jpg
Views: 2958
Size:  32.6 KB

    Today is office work day again, so little or no work today.

    I need to set up the drill fixture to cut the tails to fit 1/2" tubing. Also I have not yet made the L brackets, so I have to do that next. Then I will attach one set of brackets and check it against the actual spars for correct spacing before attaching the remainder.

    Dale
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  2. #72
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    209
    Took a break from trimming the ends and brought one lower wing structure from the hangar to set the rib spacing.

    Name:  m_DSC05148.jpg
Views: 2658
Size:  35.4 KB

    Also laid out the tip lines per the Rosendaal drawings.

    Name:  m_DSC05150.jpg
Views: 2726
Size:  67.6 KB

    I was having problems with drilling the arc in the tail of the rib. 1/2" step drill through 1/2" tubing wanted to catch just as the cut finished. This evening, I changed the blocks to oak and made them snug. I used a step bit with about 10 steps (max 1/2") at high speed in the drill press. Finally, I made the final cut through real slow and stopped the bit before I let it back up. Worked real good.

    Name:  m_DSC05161.jpg
Views: 2664
Size:  47.6 KB

    Name:  m_DSC05162.jpg
Views: 2691
Size:  61.5 KB

    Phew, the north Florida heat and humidity are killers.

    Dale
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  3. #73

    Join Date
    Aug 2011
    Location
    Alabama
    Posts
    2,236
    Very nice.

    So, is the shop apron to catch the sweat coming off your glasses or the face shield?

    (building airplanes Down South is so much fun in the summertime!)
    The opinions and statements of this poster are largely based on facts and portray a possible version of the actual events.

  4. #74
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    209
    The temperature and humidity here in the Florida have been stifling the last couple weeks, but I have braved a little time in the shop.

    All of the lower wing rib sets have been fit with the spar attachment brackets:

    Name:  m_DSC05216.jpg
Views: 2456
Size:  39.6 KB

    Trial fit:

    Name:  m_DSC05213.jpg
Views: 2550
Size:  35.8 KB

    I made one set with tabs pointing left and one set with tabs pointing right. All are clearing obstacles except the one just outside the inner compression strut. It had to be trimmed:

    Name:  m_DSC05223.jpg
Views: 2753
Size:  85.7 KB

    Then it was on to forming the wing tip bows:

    Name:  m_DSC05226.jpg
Views: 2579
Size:  86.4 KB


    Mirror image for the other tip:

    Name:  m_DSC05231.jpg
Views: 2615
Size:  82.4 KB

    Lovely assistant holding tips for comparison:

    Name:  m_DSC05233.jpg
Views: 2486
Size:  35.1 KB

    Next is to form the rear spar tips to a taper down to the 1/2" tip bow.

    Dale
    Last edited by bookmaker; 08-14-2016 at 11:50 AM.
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  5. #75
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    209
    After a lot of sweat, moaning, groaning and some pain, one wing tip is basically attached.

    Name:  m_DSC05243.jpg
Views: 2569
Size:  35.0 KB

    Name:  m_DSC05244.jpg
Views: 2666
Size:  92.6 KB

    Name:  m_DSC05245.jpg
Views: 2560
Size:  67.2 KB

    Here is the end result of raking my arm against the pointy end of a 1/2" drill bit. 3" long by about 1/8" deep slice. Nice sharp drill bit. I don't recommend trying this.

    Name:  m_DSC05241.jpg
Views: 2543
Size:  52.7 KB

    Dale
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  6. #76

    Join Date
    Nov 2012
    Posts
    45

    the heat

    Quote Originally Posted by bookmaker View Post
    After a lot of sweat, moaning, groaning and some pain, one wing tip is basically attached.

    Name:  m_DSC05243.jpg
Views: 2569
Size:  35.0 KB

    Name:  m_DSC05244.jpg
Views: 2666
Size:  92.6 KB

    Name:  m_DSC05245.jpg
Views: 2560
Size:  67.2 KB

    Here is the end result of raking my arm against the pointy end of a 1/2" drill bit. 3" long by about 1/8" deep slice. Nice sharp drill bit. I don't recommend tan inspector .

    Name:  m_DSC05241.jpg
Views: 2543
Size:  52.7 KB

    Dale
    In relation to the heat; my family lives in Perth Western Australia and about 15 years ago my brother finished a Glasair and you can imagine the heat in the middle summer here,in an aluminium shed. The civil aviation authority gave him a temp range inside of which he could work the fiberglass. So took him 9 years.He was lucky in that he had an inspector living next door. Slick machine but. Cheers Ross

  7. #77
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    209
    G'day eiclan. Thanks for looking in. I was beginning to wonder if anyone was.

    At least working with the aluminum, heat is not a concern with the material. It is not so much the actual temperature here, it is the humidity level at the temperature. It is just stifling.

    ps: I've never been to Australia, but it's on my bucket list.

    Dale
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  8. #78

    Join Date
    Nov 2012
    Posts
    45
    Pop over mate ,nice weather with 300 sunny days,on average, a year. Bring the aerplane you will love it. Cheers Ross

  9. #79
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    209
    I sent the material and drawing to my dad to machine the aileron blocks.

    Name:  m_002.jpg
Views: 2479
Size:  39.5 KB

    He found it best to cut the holes by turning on his lathe.

    Photos of progress:

    Name:  m_IMG_0528.jpg
Views: 2490
Size:  56.3 KB

    Name:  m_IMG950531.jpg
Views: 2486
Size:  46.5 KB

    Name:  m_IMG950533.jpg
Views: 2572
Size:  35.7 KB
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  10. #80
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    209
    Meanwhile, Rose and I started attaching ribs on the lower right wing:

    Name:  m_DSC05246.jpg
Views: 2407
Size:  63.0 KB

    Name:  m_DSC05247.jpg
Views: 2481
Size:  39.1 KB

    The rear plates were not attached top the rear spar until I was comfortable with the straightness of the trailing edge. So far about 1/2 of the ribs have been attached to the rear spar.

    Name:  m_DSC05254.jpg
Views: 2443
Size:  90.3 KB

    Name:  m_DSC05253.jpg
Views: 2486
Size:  43.2 KB

    I need to fabricate the plates to attach the trailing edge to the tails of the ribs.

    Dale
    Last edited by bookmaker; 08-28-2016 at 09:41 PM.
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •