Search:

Type: Posts; User: Jeffrey Meyer

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Hi Patrick, I'm guessing you're looking for...

    Hi Patrick,

    I'm guessing you're looking for libraries of non-isotropic materials?
    I'll be happy if I'm wrong but I suspect you'll have difficulty finding such a "library", because non-isotropic...
  2. Replies
    83
    Views
    81,162

    Sticky: Turns out you can get official support from: ...

    Turns out you can get official support from:

    https://www.solidworks.com/support/student-form

    Can't guarantee that you'll get a quick reply - first-come-first-serve basis, but you'll certainly...
  3. Replies
    83
    Views
    81,162

    Sticky: Hi again Floyd. This might help:...

    Hi again Floyd.

    This might help:
    http://eaaforums.org/showthread.php?9763-SolidWorks-Install-Fails&referrerid=4242

    Jeffrey
  4. Replies
    83
    Views
    81,162

    Sticky: Hi Floyd, (Hope you don't mind my inferring...

    Hi Floyd,

    (Hope you don't mind my inferring your name from your username;))
    The answer "No" is always better than the answer "don't know", so for the moment my answer to your question is "No, I...
  5. Replies
    83
    Views
    81,162

    Sticky: Can't say I understand what you're trying to do....

    Can't say I understand what you're trying to do. Try Insert>Boss/Base>Sweep... or you can find Swept Boss under Help with detailed explanations on how to use it.

    Also, could you share some...
  6. Replies
    83
    Views
    81,162

    Sticky: Can you live without the "curved edge flange"...

    Can you live without the "curved edge flange" feature for a few months?

    In the vast majority of cases ( I would even gamble on saying "always") there's a work-around: In the meantime maybe you...
  7. Replies
    83
    Views
    81,162

    Sticky: Once again, installation issues are not my forte,...

    Once again, installation issues are not my forte, but I know that you are not "stuck" with the version you installed. As I said in my last post the Student edition lags behind the commercial edition...
  8. Replies
    83
    Views
    81,162

    Sticky: My limited experience with the student edition is...

    My limited experience with the student edition is that it is published with a kind of "phase lag" of about half a year (or maybe even a full year) relative to the commercial version. So if I were...
  9. Replies
    83
    Views
    81,162

    Sticky: I would answer if I could, but I have very little...

    I would answer if I could, but I have very little knowledge of installation issues and zero authority to contact DS SolidWorks support.
  10. Perfectly legit to mate in terms of edges, but...

    Perfectly legit to mate in terms of edges, but edges are usually only 2D and you might end up with the problem you had at the beginning of this topic.
  11. Hi Jeremy, In assemblies try the following...

    Hi Jeremy,

    In assemblies try the following unless you have no other choice: Mate to planes and/or faces rather than wire-frame geometry.

    Jeffrey
  12. Hi Jeremy, This seems to be an unusually...

    Hi Jeremy,

    This seems to be an unusually strange phenomenon, but I was able to recreate it albeit using (much-more-logical;)) metric units:

    I suspect the problem is that your 8in distance is an...
  13. Replies
    3
    Views
    846

    Hi MB107, Your mummy must be very proud of...

    Hi MB107,
    Your mummy must be very proud of giving you such a unique name:)

    I may be mistaken, but as far as I know there is no utility that enables you to translate Catia files to SolidWorks. ...
  14. Replies
    12
    Views
    1,983

    Propeller vs Impeller, incompressible vs...

    Propeller vs Impeller, incompressible vs compressible flow, extremely low rotor solidity vs extremely high rotor solidity. Completely different engineering design criteria.
    Propellers are rotating...
  15. Replies
    12
    Views
    1,983

    Words of wisdom, with the emphasis on...

    Words of wisdom, with the emphasis on "Excepting". The VW is truly an exception.
    Automotive engines are engineered for automobiles, and aircraft engines are engineered for airplanes, with...
  16. Replies
    12
    Views
    1,983

    Prop efficiency is inversely proportional to prop...

    Prop efficiency is inversely proportional to prop diameter. As the saying goes "keep it as long as possible as long as possible". So theoretically the most efficient prop for a given airspeed and...
  17. Replies
    3
    Views
    1,562

    Hi Mark, Skydawg. Prop design is as much an...

    Hi Mark, Skydawg.

    Prop design is as much an art as it is a science and it includes no small measure of aesthetics. It is not by chance that there are several very reputable companies that...
  18. Replies
    4
    Views
    1,202

    Hi RCS There is a SolidWorks Tutorial called...

    Hi RCS

    There is a SolidWorks Tutorial called "PhotoView 360 and Appearances"​ that shows you how to do this by applying Decals to the face(s) of your panel.
  19. Replies
    4
    Views
    1,731

    It's also an operating system issue. My...

    It's also an operating system issue. My long-in-the-tooth DELL machine ran SW under Windows 7, and when I upgraded the OS to Windows 10 I discovered that it (Windows 10 and NVIDIA) didn't have an...
  20. Sticky: Hi Alan, Like most CAD software SW demands a...

    Hi Alan,

    Like most CAD software SW demands a combination of ALL computer resources - RAM, Disc, Clock speed, etc. including hardware graphics, and you can't have too much of any of them:eek:.
    ...
  21. Replies
    27
    Views
    19,213

    My installation worked just fine first try using...

    My installation worked just fine first try using Chrome - I haven't used Internet Explorer for many years. Maybe I have better connections in the Holy land;)

    Happy new year.
  22. Replies
    4
    Views
    3,157

    souza13alex said: Agree absolutely. Also...

    souza13alex said:



    Agree absolutely. Also want to know what drone you're using. I'm working on converting an 800 size RC helicopter to an airborne photographic platform, including a Pixhawk...
  23. Replies
    3
    Views
    1,895

    You can also use the "box" part as a multi-body...

    You can also use the "box" part as a multi-body part - no assembly necessary.
    Add a Derived Configuration of the box, calling it the "lid".
    On the top surface of the box create a sketch of the...
  24. Sticky: Hi Joe, Every word cast in rock !! I find it...

    Hi Joe,
    Every word cast in rock !! I find it incredible and completely fail to understand why this is so. In fact, the only way you can communicate between the packages is via the CAD interface...
  25. This is somewhat off-topic, but I couldn't resist...

    This is somewhat off-topic, but I couldn't resist the temptation to make this post:
    IMHO torque and moment are 100% synonymous and interchangeable. The use of one or the other is entirely part of...
Results 1 to 25 of 191
Page 1 of 8 1 2 3 4