Printable View
Wood propellrs Meglin to any engine can be designed and manufactured in a short time.
Wood - Beech.
Protection glass and stainless steel.
Details on the website: http://propeller.simplesite.com/
Please feel free to ask me any questions - consultations are free.
It Skyranger with VW-1600. Series propeller SDW-1.
http://cdn.simplesite.com/i/2f/e6/28...1280h1280_.jpg
Deleted my post complaining about commercial use of this space, but it does seem a somewhat inappropriate use.
I sell handmade individual samples. And I do not have a place of business.
We rest until the end of September.
Please feel free to ask me any questions - consultations are free.
The attach bolt holes in the hub seem a bit close to the edge, Vladimir, compared to props made in the USA. Have you performed any stress analyses and pull-out tests to verify there's enough wood in the hub?
This screw series SDV-1 runs on a motor trike Limbach 10 years. It has excellent characteristics. Developer considered it acceptable - it guarantees.
This propeller has just been sent to France. It is intended for an aircraft engine with O-320 and the speed of 232 km / h. The propeller has a limited diameter of 1700 mm.
Special airfoil was designed to increase starting traction and reduce noise.
It is possible to avoid stall at all speeds. Standard profiles are not suitable.
Propeller for Limbach
More foto.
Limbach
"At long last I have flown my new aeroplane with your prop. It was only the first flight yesterday and for just 30 mins. My first impression is that the prop is very good match for both the 0320 and my airframe. The climb rate was up to 1500ft/min and level cruise at 2200/2300 revs nearly 120 Kts after only a very rough short evaluation. I think the 75% cruise will be 130kts so the prop must be very near to the best compromise available.
As you know many Vans 6 owners use the popular 0320 lycoming and the Vans is very similar in general configuration (but not construction) to my airframe so this spec prop should work well. As the Vans is very popular there should be a good market for your product"
These propellers went to France. Designed for Limbaсh and for Jabiru.
Individual design and manufacture of wooden propellers.
We continue to design and manufacture propellers for individual orders. Handmade.
1/2 VW
propeller just sent
This propeller is designed for Peugeot engine.
The queue of customers has decreased significantly - now we do faster, about 1 month.
Dear colleagues! The number of orders for wooden propellers has increased dramatically. We don't have time. I must warn potential customers that the propeller will have to wait several months. We can't compromise the quality of the product.
New propeller for Sauer engine
Some photos
Are these wooden propellers laminated, or one solid piece of wood ?
Bob
Is it possible to make propellers from a single piece of wood?
A strange questions:
Oddball Lycoming 0-320-G engine with counter-clockwise rotation...
Would it be possible to use it with a reverse-engineered prop?
What can prevent it?
I hope the customer likes it.
We are expanding production. The term of execution of an individual order is reduced to 3 weeks.
Decorative wooden propellers.
Small price, high quality.
The diameter is from 0.5 to 2.5 meters.
Any form.
Hand-made to order
....
Finishing up the propeller with an aviation clock.
I will sell a decorative propeller with a diameter of 145 cm (see photo). The price is 90 euros.
The German customer is satisfied. Me too.
There is a new 72*44 wooden propeller on sale. Right rotation. SAE-2. The material is beech. It is covered with fiberglass. The edges are stainless steel.
Another propeller for VW
Propeller 54*26 designed for 1/2 VW. Due to ignorance of the exact power of the engine, we made its diameter with a margin. The operator plans to cut the blades in stages until optimal revolutions are achieved on the ground and in flight.
After a hiatus, production of decorative propellers has resumed. The photo shows old blades that can be used for souvenirs.