PDA

View Full Version : Does anyone recognize this part?



treddie
01-17-2015, 03:00 PM
Hello.

I hope this is the correct forum for this.

I was curious if anyone notices this vintage part? It comes from probably the late 1950's to mid 60's and was used for the interior of the space pod in the movie 2001: A Space Odyssey, which I am back-engineering. There were a number of surplus aircraft parts used in the movie, and I was hoping someone might be able to identify this particular one, if in fact it is of aerospace origin.

I'm thinking there might be a spring under the retaining ring on the side. So it makes me think this was a pressure regulator or flow control device of some sort. Or a pump...The shaft coming out on the left looks like it might be a spline shaft, but the photograph is not good enough to tell for sure. I have removed all of the surrounding details in the image in Photoshop, since they basically just stuck this thing on the cabin wall.

Many thanks for taking a look. :)

http://eaaforums.org/attachment.php?attachmentid=4457&stc=1

rwanttaja
01-17-2015, 06:51 PM
One possibility might be a 90-degree gear box... input shaft comes on the left, gear inside to rotate a similar shaft on the top back. The apparent cap could just be to open the gear box so it can be packed with grease...

Ron Wanttaja

1600vw
01-18-2015, 07:05 AM
Ron I would agree. It looks to be some sort of worm gear box. Maybe steering box out of an old car. But it sure does look like a worm gear box to me.

rwanttaja
01-18-2015, 12:18 PM
Ron I would agree. It looks to be some sort of worm gear box. Maybe steering box out of an old car. But it sure does look like a worm gear box to me.
I like the suggestion about the steering box...something cheap and common that they could easily find for the movie prop.

Treddie, any indications of size of this thing, in the movie? Are there any scenes with the astronauts in the frame with the device, that you could use to figure out the scale? Or was this on a miniature?

Ron Wanttaja

treddie
01-18-2015, 04:48 PM
Hey everyone. First of all thank you for the excellent replies!

The object is roughly 3" square on the face. Unfortunately, there are only two images which shows it well, and the other image has it in shadow...Just visible enough to tell it is the same gadget. Now, it also has another "port" on the far, hidden side, which led me to believe that the one on top and the hidden one were either gas or fluid fittings. But that could be caused by the fact that they stuck a hose on the top one, which biases my thinking. It may very well be a gear box as you all suggest. But notice that the top fitting has a hex nut at its base. Would a gear box treat a shaft exit point like that? That was another reason why I thought it might be a pump or something. Also, what we see MAY only be the visible exposed portion, if the remainder of it is behind the wall.

I will do more research, but take your tack of checking vintage auto parts. Maybe it IS a gear box.

1600vw
01-18-2015, 05:34 PM
I believe that nut would set end play.

treddie
01-19-2015, 01:33 AM
Hm. Interesting thought. So it would act as a friction brake then?

1600vw
01-19-2015, 06:19 AM
Hm. Interesting thought. So it would act as a friction brake then?

End play has nothing to do with a friction brake. End play or backlash is just that the adjustment of the play or backlash between the two shafts. A worm gear steering box if you do not adjust the end play on the worm shaft coming out of the box, the steering wheel well have a lot of play in it. On a steering system you do not want the steering wheel to turn a 1/4 turn and not move the wheels. The steering wheel should not have a bunch of play back and forth. Its this nut that would remove this play. It has nothing to do with a brake. But to remove play between the two shafts.

In the automotive world we call this road feel. Set it to tight and your car will be twitchy. Set it to loose and you will be moving the steering wheel back and forth and nothing happens at the steering wheels. You have excess play in the steering wheel. A modern steering box has a set screw one uses to adjust this play. I would say this is the end play or backlash adjustment on this unit.

In the modern car today we use what is called a rack and pinion. That removes this gear box. Those type of cars do not use a gear box such as this. Pickup Trucks today still have a worm gear steering box as do a few cars but most has gone to rack and pinion steering.

Blue Chips
01-19-2015, 09:14 AM
Reminds me more of a hydraulic motor or pump although can't see the 2nd line, maybe hid on the back side, the way it bolts the sections up doesn't at all look familiar for a steering gear box.

1600vw
01-19-2015, 10:20 AM
Reminds me more of a hydraulic motor or pump although can't see the 2nd line, maybe hid on the back side, the way it bolts the sections up doesn't at all look familiar for a steering gear box.

Not for a modern steering gear box or one in a car or truck. But what about a 1900's and something say small tractor or even a car. A pump motor case will not look like this but will be more square. Its does not have the same internals that would need the case as this does.

1600vw
01-19-2015, 10:23 AM
Pump motor

http://eaaforums.org/attachment.php?attachmentid=4461&stc=1

1600vw
01-19-2015, 10:30 AM
Old steering box from a tractor.

http://eaaforums.org/attachment.php?attachmentid=4462&stc=1

treddie
01-19-2015, 02:41 PM
After doing some research last night, I think it really IS a pump. Out of all the images I perused, the closest matches were for hydraulic pumps (Please see the attached images).

BlueChips > That second line is on the back side, opposite the side with the retaining ring, and is on that same aft block of metal, like the fitting on top. You can just barely see it in a second image.

http://eaaforums.org/attachment.php?attachmentid=4463&stc=1 http://eaaforums.org/attachment.php?attachmentid=4464&stc=1 http://eaaforums.org/attachment.php?attachmentid=4465&stc=1

Blue Chips
01-19-2015, 02:52 PM
No gear box, it's some type of hydraulic unit, that's my story and I'm sticking to it ! :)

Blue Chips
01-19-2015, 02:55 PM
Pump motor

http://eaaforums.org/attachment.php?attachmentid=4461&stc=1

Corrected "New Pump Motor" as opposed to "Old pump motor" LOL

treddie
01-19-2015, 03:54 PM
Well...To add to the debate, here are two more images of "The Mystery Part", and why I am leaning towards a pump.
The first image shows the part from a different angle and shows the second fitting. The second image shows that there may be a press fitting, or a raised bump at the end of the fitting to hold a hose with a pipe clamp (pipe clamp missing):

http://eaaforums.org/attachment.php?attachmentid=4466&stc=1 http://eaaforums.org/attachment.php?attachmentid=4467&stc=1

1600vw
01-20-2015, 03:50 AM
From the pic you can see a snap ring on one end.

See anything that looks the same in this pic? This gear box may be bigger but I still believe you are looking at some sort of gear box.

http://eaaforums.org/attachment.php?attachmentid=4468&stc=1

treddie
01-20-2015, 07:22 PM
Possibly. Very frustrating not being able to know for sure what it was. If I knew for sure, I could get the part out of some bone yard and measure the thing.

Blue Chips
01-20-2015, 07:54 PM
You know, 1600vw could be right, but only half right :)
There are steering gear boxes that are hydraulically operated, fairly common in tractors.

martymayes
01-20-2015, 08:19 PM
You know, 1600vw could be right, but only half right :)


No partial credit allowed on a "Does anyone recognize the part?" thread...... :)

Blue Chips
01-20-2015, 08:24 PM
Your a tough one ! :)

treddie
01-21-2015, 10:05 PM
The plot thickens...My brother thinks its a gear box, too. My head is going to explode! I have also posted this question at a hydraulics forum. No responses back yet.

Qmiester
02-01-2015, 02:03 PM
I'm probably wrong,but it looks a lot like part of an old cowl flap operating system - maybe the end unit.

treddie
02-03-2015, 03:14 PM
I'll check into that.

1600vw > Sorry I didn't respond to your earlier post about "End play has nothing to do with a friction brake." I should have known better since about half a year ago I had to study up on bevel gears, and the end-play thing should have immediately registered.

treddie
02-16-2015, 04:59 PM
No luck tracking down cowl flap actuators. Not that it could not be one.

On the idea of it being a 90deg gearbox, there is one problem that bothers me about that. If you look at it, you'll notice that the vertical shaft is all the way in the back, so there is no room for a bevel gear to fit back there (assuming we are seeing the entire length of the case). Other than that, the snap ring and cover are situated too far forward to be able to inspect a bevel gear that would be all the way in the back.

treddie
02-17-2015, 07:59 PM
I just noticed something else. If you look at the shaft coming out of the side, right next to it is a little tab like thing. That could be a hard stop. In other words, the shaft may not be a free-rotating shaft, ruling out both a pump and gear box. The shaft may have had a knob or lever attached to it that would travel only as far as the hard stop would allow. If that is true, this could be a hydraulic controller or some other type of valve.

Qmiester
03-26-2015, 07:20 AM
Looks a lot like part of the cowl flap operating system on an old radial engine.

Charles R Nelson
03-28-2015, 02:07 PM
First thought was a vacuum pump driven off the engine for instruments and old aircraft used vacuum for flaps. How long is the shaft coming off of it?