View Full Version : Can anyone help ,what is it.........
I am papasmurf
10-19-2013, 09:01 AM
Found in a grandfathers barn and have no clue....I am not a collector nor a flyer,although i do have over 230 hours in a ultralight,long story short is i dont wont to crush anything of value or something that another could use,any thoughts will be helpful..........Special thanks to Hal for his help........Jim Rogers3346334733483346
rwanttaja
10-19-2013, 09:26 AM
Globe/Temco Swift.
http://www.airfields-freeman.com/TX/GlobeSwift_GC-1A_48.jpg
Ron Wanttaja
JimRice85
10-19-2013, 10:17 AM
Yes. Definitely a Swift. Ron's picture is of a Continental C-85 powered GC-1A. After a few hundred, the decided to use the Continental C-125, which was a big improvement, and designated GC-1B.
Hard to tell which the one you saw is. Airframes were virtually identical. It is likely a 46-48 model when Globe was building them, with Temco also building under contract. Globe later went under and Temco took over and built more 1950-51, IIRC. the rear windows and hat throw behind the seats was changed.
Here is my 1946 Globe Swift.
http://home.comcast.net/~jimrice85/ATT00002.jpg?PHPSESSID=6df6d5ca57d67738778affc3c64 0786b
http://home.comcast.net/~jimrice85/swiftflying.jpg?PHPSESSID=6df6d5ca57d67738778affc3 c640786b
I am papasmurf
10-19-2013, 11:44 AM
First off MANY THANKS ,you guys were very fast,and i wish it was all there,i had no idea that this plane would look any thing like this,i was trying to put it in the J2 class which i have flown some years ago,but it is about in a class to itself,the alclad is what made me wont to look further,i will leave this post up for awhile longer to see if anyone may need any sheet metal,it has several more parts in the belly of the plane that i have not pulled out and the rt fuel tank is still in the wing,just dont seem right to crush it...........................
JimRice85
10-19-2013, 12:13 PM
Where are you located? I'd be interested in learning what parts may remain. Also interested in the remaining fuel tank. Are there any rudder pedals or other control linkages?
I am papasmurf
10-19-2013, 02:56 PM
I have the rt wing tank and 4 pedals,here is another picture i have ,i will also get you some better pictures of what i have.
I am papasmurf
10-19-2013, 03:00 PM
You can see the pedals....
I am papasmurf
10-19-2013, 03:04 PM
I forgot Location Maryville Tn. Phone 865 257 5717.......Thanks Jim Rogers
GodsCowboy
10-20-2013, 08:58 PM
What an awesome find... IF only it could tell us it's story.
I am papasmurf
10-21-2013, 04:31 PM
Well i went got the camera an pulled the sheet metal out of the belly,it really looks like most of the covering is in good shape,the gastank was sealed with tape.most hard part controls are ok,but the cables are rusted,the entire body of this plane ,at least what is left, dont weight 100lbs.............
I am papasmurf
10-21-2013, 04:51 PM
Here are mor pics336033613362336333643365336633673368
JimRice85
10-21-2013, 07:59 PM
It has seen better days, that's for sure. The rudder/brakes pedals (on left side) look like they have some corrosion on them to the point I'm not sure they would be usable. I'd be equally concerned with the gas tank if it has been left outside.
Without being able to see it in person, I'd be hard pressed to offer much for the parts. I'm over in Memphis. Were it closer, I might be interested in buying and dragging it home. I'm just afraid what little is left isn't useable.
You might want to contact Swift Works in Dayton, TN or the Swift Museum Foundation in Athens to see if they are interested in it.
I am papasmurf
10-22-2013, 07:59 AM
It has seen better days, that's for sure. The rudder/brakes pedals (on left side) look like they have some corrosion on them to the point I'm not sure they would be usable. I'd be equally concerned with the gas tank if it has been left outside.
Without being able to see it in person, I'd be hard pressed to offer much for the parts. I'm over in Memphis. Were it closer, I might be interested in buying and dragging it home. I'm just afraid what little is left isn't useable.
You might want to contact Swift Works in Dayton, TN or the Swift Museum Foundation in Athens to see if they are interested in it.
I will contact them to see if any interest if not it will go for scrap,again many thanks Jim Rogers
JimRice85
10-22-2013, 08:50 PM
I will contact them to see if any interest if not it will go for scrap,again many thanks Jim Rogers
If you go scrap route, I'd still be interested in gambling on the actual left side rudder pedals and the gas tank.
I am papasmurf
10-23-2013, 09:23 AM
If you go scrap route, I'd still be interested in gambling on the actual left side rudder pedals and the gas tank. Jim, I spoke with Pam at the Swift Museum and and she was more then helpful,also she dont wont to see the plane scraped,so at this point i have agreed to work with her to save all parts untill she view the photos,and she is only 45 mile from me.I will keep you posted here as i find out what the outcome will be.......Jim Rogers
JimRice85
10-23-2013, 07:08 PM
Jim, I spoke with Pam at the Swift Museum and and she was more then helpful,also she dont wont to see the plane scraped,so at this point i have agreed to work with her to save all parts untill she view the photos,and she is only 45 mile from me.I will keep you posted here as i find out what the outcome will be.......Jim Rogers
Tell Pam she owes me. :). Hope it works out. Going to Swift Museum is best deal, IMHO.
I am papasmurf
10-29-2013, 07:41 PM
Tell Pam she owes me. :). Hope it works out. Going to Swift Museum is best deal, IMHO.
Jim,Many thanks for your help,the plane made it to Pam and she seemed happy to get it,i told her that she owed you one she laughed and and said she would probably hear from you soon,again many thanks.......Jim Rogers.
Powered by vBulletin® Version 4.2.4 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.