Page 1 of 2 12 LastLast
Results 1 to 10 of 22

Thread: Homebuilt, low wing, 5+2 place, mazda powered twin

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1

    Join Date
    Dec 2018
    Posts
    15

    Homebuilt, low wing, 5+2 place, mazda powered twin

    Hi all,
    I am currently 15 and working on getting my private pilot license. My dad has a Grumman AA1B, but we have always wanted something a little bit bigger (we are a big family of 7). I am very good with mechanical stuff and problem solving. I recently decided that i would like to build my own plane. I know it seems like a very ambitious project, but i am not expecting to finish it any time soon. The plane is going to be a 5 + 2 place (there will be 5 main seats and 2 removable jump seats for small people in the cargo area in the back of the cabin) low wing RG twin. My plane is going to be very heavily based on the Diamond DA-62 (it will have a straight tail). It will have a wingspan of about 33 feet, with an LOA of 26 feet. it will weigh about 3500-4000lbs and be powered by 2 (heavily) modified 13B Wankel engines from the Mazda RX-7; each engine will hopefully put out about 700bhp. The cabin and interior is heavily inspired by the Diamond DA-62, with a 3 place bench seat in the middle, and a large cargo area behind the bench seat. due to the size of the cargo area, there will be 2 removable "jump seats" that can seat people up to roughly 100lbs. I will be developing all of the systems that do not pertain to avionics myself (engine instruments, safety systems, etc.) with the help of my good friend (for all the computer related stuff). The plane has a very heavy focus on safety, with 2 fully redundant electrical systems and separate flight computers. There is a built in fire suppression system that has access to both engines, cabin and all cargo holds. The cabin is a completely sealed (not pressurized sealed, just sealed from all liquids) and there are no fuel lines that run through the cabin. The cabin is also completely encased in an aluminum structure that adds rigidity to prevent deformation in case of a crash. The 2 feet of the wing closest to the root is reinforced to prevent bending and jamming doors closed. the doors are a traditionally opened (like a Cherokee) and the frame around the door is reinforced with steel to prevent deformation. The plane will also be equipped with a trailing link, hydraulically retractable gear. the reason that I choose a trailing ink setup is because it allows the aircraft to land on rough strips without the concern on collapsing the nose gear. The flight controls are all linked to the control stick (no yoke) using control rods instead of cables; additionally, the aircraft will be fitted with a 2 stage flap system (will explain later, its complicated) that will allow the flaps to come down in more gradual notches from barely down to being a giant barn door. The plane will also be equipped with an electronically controlled spoiler system and constant speed, fully automated (no prop lever), reversing propellers. There are many other aspects that I would be happy to discuss, just let me know. I realize that it may seem like the plane is already built but it is still in the "drawing in a notebook" stage, (with a lot of dreaming).

    I mentioned powering it with 2 wankel engines from the Mazda RX-7. I am wondering just how common this is (i have seen a few youtube videos on it, but only 2 or 3) and how hard it would be to do. i have browsed the rx7 forums, and given that you can get 750 bhp from a 2 rotor 13b if you push it, i do not think that 700 would be that bad. if there are other engine ideas, then please let me know. i would like to keep it above 400 hp per side and keep the cost under 15k per engine (a 13b is about 8k for a remanned one) and associated equipment. i would also like the engine to be liquid cooled and burn about 12 gph at max (preferably mogas).

    if you have any pointers for me, then please let me know, because despite how much help i already have (several mechanical engineer friends are willing to help me), i am searching for any tips i can possibly find. if you have another idea, then let me know, and if there is anyone who has done anything remotely similar to what i am trying to do, then please let me know...

    thanks,
    Christian L.

  2. #2
    cwilliamrose's Avatar
    Join Date
    Nov 2013
    Location
    SW Florida
    Posts
    177
    Pulling that much HP out of an automotive engine is going to be a problem. The duty cycle in cars is completely different to an aircraft -- where the car may pull high HP for a short time an aircraft needs that power continuously. Also, think about how many family members will be wanting to go on trips in the airplane by the time it's finished and developed enough to carry passengers. That number could change a lot in 10-15 years.

  3. #3
    cluttonfred's Avatar
    Join Date
    Oct 2011
    Location
    World traveler
    Posts
    447
    Christian,

    Welcome to the EAA Forums. If you haven't already, you might also think about joining the HomebuiltAirplanes.com forum, which is not affiliated with any group. Both are great resources. You project sounds very ambitious--very large, very complex, and hugely boosted engines. Personally, I would suggest something more modest as a first step--say building an existing, proven, simple, single-engine, one- or two-seat homebuilt. As you look around online and in the magazines, you'll find that twin-engine hombuilts are very uncommon, certainly less than 1% and probably less than 0.1%. Ditto anything with more than 300 hp or so, period. I don't want to discourage your enthusiasm, but what you've described is like saying, "I want to build my own home and I want it to be a 40-story skyscraper" instead of starting with, say, a small cabin as a first step.
    *******
    Matthew Long, Editor
    cluttonfred.info
    A site for builders, owners and fans of Eric Clutton's FRED
    and other safe, simple, affordable homebuilt aircraft

  4. #4

    Join Date
    Oct 2011
    Posts
    151
    Quote Originally Posted by cluttonfred View Post
    As you look around online and in the magazines, you'll find that twin-engine hombuilts are very uncommon, certainly less than 1% and probably less than 0.1%.
    Exactly! There is a surplus of small single-engine homebuilt designs that can't carry much very far. Which is fine if that's what you want. In constrast, there are woefully few homebuilt designs to choose from that can carry 7 people. As pilots decline as a percentage of the population, the fleet needs more aircraft that can carry more passengers per crew member.

  5. #5
    rwanttaja's Avatar
    Join Date
    Jul 2011
    Location
    Seattle
    Posts
    2,296
    Quote Originally Posted by cluttonfred View Post
    Christian,

    Welcome to the EAA Forums. If you haven't already, you might also think about joining the HomebuiltAirplanes.com forum, which is not affiliated with any group. Both are great resources. You project sounds very ambitious--very large, very complex, and hugely boosted engines. Personally, I would suggest something more modest as a first step--say building an existing, proven, simple, single-engine, one- or two-seat homebuilt. As you look around online and in the magazines, you'll find that twin-engine hombuilts are very uncommon, certainly less than 1% and probably less than 0.1%. Ditto anything with more than 300 hp or so, period. I don't want to discourage your enthusiasm, but what you've described is like saying, "I want to build my own home and I want it to be a 40-story skyscraper" instead of starting with, say, a small cabin as a first step.
    I'd like to echo Matt here. This *is* a highly ambitious project, and you probably would be better off to scale things down a bit.

    Developing and testing a new auto-engine conversion will take the same amount of time...or more...than the building of the airplane. Reliable auto-engine conversions have been rare; the accident rate for auto-powered homebuilts is significantly higher than for traditional engines.

    In the archives of the EAA Forums you'll find at least one thread dedicated to the Twin Jag aircraft, an RV-6 with two Corvair engines. The first posting was over five years ago; the airplane just recently flew for the first time.

    Consider: The builder took a flying RV-6, and installed two Corvair engines (which are commonly used on homebuilts) and it STILL took him over five years.

    If I were you, I'd bag the Wankels. There are a lot of older twin-engine aircraft that can be bought for a song; use one to supply engines for your project. Considering the large size of the aircraft, you MIGHT consider turboprops.

    Like Matt, I recommend you build something NOW; something you can reasonably complete in a reasonable amount of time. Something like an RV would be perfect, considering you're planning to build your dream bird out of aluminum. Work on the new design while building the RV. You'll undoubtedly learn a lot in the process that could be used to make your design better. Once the RV is completed, you can start building the new design. The RV would keep your skills sharp while the new plane goes together.

    Ron Wanttaja

  6. #6
    Dana's Avatar
    Join Date
    Jul 2011
    Posts
    784
    Welcome Christian,

    As others have said, you're proposing a really ambitions project... one that even most experienced aircraft designers would shy away from. Designing even a simple aircraft is not a simple thing, and the complexity of a fast twin with all its systems makes it several orders of magnitude more difficult. Without going into the big picture, let's focus on a few aspects of your proposal:

    First, the engines. Yes, Mazda rotaries can make absurd amounts of power... for a very short time. So can big block V-8's and other automotive engines. The problem, in an aircraft application, is usually cooling those engines. A drag racer runs for a few seconds and shuts down, the engine has time to cool afterwards... and even so, the engines only last for a few races. Another issue is engineering the reduction drive... you can't efficiently turn a propeller at the rpm a modern auto engine is turning, so you need a redrive. Reduction drives look simple, but the engineering to make one reliable is anything but. Torsional resonance is just one of many issues that have ended many otherwise promising designs.

    Marine engines are heavy and have an unlimited amount of cool water available for cooling.

    You're talking a lot about minor details like fire suppression systems, landing gear geometry, and control linkages. It's tempting to get interested in those details because they're easily comprehensible, and many inexperienced designers make the same mistake of fixating on the little details before the basic configuration is worked out, I've been guilty of it myself. But it's way too soon to worry about those kinds of details.

    Now, let's compare your concept with the Diamond DA-62 you mention. You're assuming a similar weight, but a much smaller aircraft 33 vs. 48 foot wingspan), with a lot more power (never mind that the power isn't realistic). Have you considered what that means in terms of stall speed and runway requirements (not to mention pilot skill)?

    Don't stop dreaming, but at this stage of your aviation experience, focus on learning to fly and learning more about what's out there, both production and experimental airplanes. See what ideas work and what ones haven't been successful, and why. You can learn a lot about designing and building with R/C models and ultralights. In a few years you'll be much better able to judge what's realistic (or useful!) and what's not.

  7. #7

    Join Date
    Dec 2018
    Posts
    15
    I want to say thank you again for all the advice and support. before i go on, i just want to clarify one thing. while it may seem like i am diving into this project all at once, i am nowhere near even close to completed designs. this project is sort of a dream that i will continue to follow through college and beyond. right now, i am really just in the basic conceptual design and "information gathering" stage. i am just trying to gather as much information as i can (even if it does not pertain to this project)... because of this, i do not expect to start construction until at least my freshman year of collage.

    after having done some more research and asking more questions, i do agree that what i said regarding power levels is pretty unrealistic. although, i still stand by what i said about rotaries being my engine of choice, however, i am now also seriously considering an LS2 or LS3 just because of the raw power that they put out. but i think that a wankel might be a little bit easier to adapt... if i could get 325 hp out of the wankels, or 500 out of the LS (if i were to use that), then i would be happy.

    as for what Ron said about using a turbine, i seriously considered using this (https://www.pbs.cz/en/our-business/a...gine-pbs-tp100), which would be perfect given that it has 241 hp, but i have read the cost is over 150k, which is way beyond my budget range.

    as i said, thanks again for all the help and advice, and please continue to share knowledge...

    thanks,
    Christian L.

  8. #8

    Join Date
    Oct 2011
    Posts
    151
    AMDguy, is your goal to build a one-off plane to carry your family, or to sell plans/kits or factory-built planes, or to prove the rotary engine?

  9. #9

    Join Date
    Dec 2018
    Posts
    15
    my goal is to build a practical, useful plane that can carry my family while having fun and learning a lot in the process...

    Christian L.

  10. #10
    Sam Buchanan's Avatar
    Join Date
    Nov 2011
    Location
    KDCU
    Posts
    486
    Christian, I applaud your endeavor to obtain your ticket! My suggestion is to continue your training to include instrument and multi-engine ratings as you consider your aircraft design. You will need those ratings to utilize a twin-engine aircraft.

    Mazda-based rotaries have been used on a few aircraft but they require a tremendous amount of engineering along with complex gearboxes. They are usually limited to ~200hp in order to obtain some degree of reliability.

    Best wishes for an enjoyable pursuit of your ratings!
    Sam Buchanan
    The RV Journal RV-6 build log
    Fokker D.VII semi-replica build log
    YouTube Channel

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •