Results 1 to 10 of 11

Thread: Magneto malfunction??

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1

    Join Date
    Nov 2011
    Location
    Texas (CowTown USA)
    Posts
    4

    Magneto malfunction??

    I recently developed an ignition discrepancy issue and can't seem to conquer.

    After performing initial engine start on the O-360 A3A, Itypically wait until engine is no less than 100 degrees before making a runupfor magnetos and other systems checks.
    This particular morning, while performing mag checks at 1800rpm and making sure all systems were in good working order, the right mag hadit’s usual 30 to 50 rpm drop. Returningselector switch back to both mag allowing rpm to stabilize and subsequentlyswitching to left mag, I experienced a continued backfire. Switch back to both and was experiencing arough running engine. Cylinderscompression check all at 78 and 79 while timing set at 25 º BTDC and both mags sync within 1/2 ºor less.

    My first thought was that this mag just went south on me andsince I had a recently 500 hr inspection done on another set of mags, decidedto replace it. After engine start, leftmag continued to run rough (no backfire) and new set of spark plugs installed. Another start and engine continued to runrough. Check the p-leads and all seemed to have the proper resistance,continuity and no short. I purchased a new set ofspark plug leads and engine continued to run rough. Replaced the ignition switch with no changeto the discrepancy.

    Because the engine rough running is isolated to left mag, I’veruled out induction system issue. Idecided to remove the newly installed left mag and reinstalled originalmag. Engine start once again resulted incontinued backfire.

    Could the issues of left mag backfire be a coincidence and newmag rough running be related to bad condenser and or bad e-gap set? Any suggestions?

    In CowTown USA,
    DonDDay
    In CowTown USA,
    Don D-Day
    N18DD

  2. #2

    Join Date
    Oct 2011
    Location
    WA
    Posts
    1,205
    Could be bad impulse if you are reusing the old one.

  3. #3

    Join Date
    Aug 2011
    Location
    Wachapreague Va.
    Posts
    247
    Plug wires crossed on left mag ?????. Check and recheck.

  4. #4

    Join Date
    Jun 2015
    Posts
    17
    Backfiring? Thru the exhaust? or the intake?
    Could be a valve sticking at operating temps & rpm's but not at cranking or testing speeds.
    Try some AV Blend and/or Marvel Mystery Oil & see if that helps. Borrow a laser temp gauge & check exhaust temps.
    That will tell which cylinder it's on. Lycoming has a "fix" that doesn't require pulling the jug.

    John

  5. #5

    Join Date
    Nov 2011
    Location
    Texas (CowTown USA)
    Posts
    4
    Thank y’all for the suggestions.


    1. Engine was running just fine for well over 350 hoursand problem began at runup prior to flight which did not, nor will it happen untilissue is fixed.
    2. Impulse coupling checked after removal andreplacement of mag and certainly audible when propeller turned through allcylinders (on two separate mags) during timing and mag sync. One mag backfires, the other one, rough (nobackfire).
    3. Compression check revealed pressure in the 78-79range with no indication of sticky valve. MMO in fuel religiously used.
    4. Backfire appeared to be exhaust and not whenright mag selected.
    5. Exhaust temperatures with laser all in the 320º to 390º range.

    In CowTown USA,
    Don D-Day
    N18DD

  6. #6

    Join Date
    Oct 2011
    Location
    WA
    Posts
    1,205
    If the impulse spring breaks it can run rough. It still clicks, but wrong timing.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •