Page 20 of 20 FirstFirst ... 10181920
Results 191 to 197 of 197

Thread: Airdrome Aeroplanes Nieuport 17

  1. #191

    Join Date
    Aug 2011
    Location
    Alabama
    Posts
    2,002
    Yep, I meant washout....setting the dihedral was a cinch.

    I really don't have washout on the lower wing, though the handwritten addition said to put it in there - no washout on the upper wing.

    I'll have to scan that page.
    The opinions and statements of this poster are largely based on facts and portray a possible version of the actual events.

  2. #192
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    193
    The first attempt attempting to cover the rudder didn't go well. I think the adhesive I have is too old and gone bad. We were able to clean off the adhesive by rubbing it like rubber cement. I ordered new adhesive so will try again.

    Rose and I reworked the V strut patterns and got both mounted temporarily.

    Name:  m_IMG_7416.jpg
Views: 73
Size:  85.6 KB
    Just had to try out the "pilot's" seat.

    Name:  m_IMG_7413.jpg
Views: 75
Size:  76.2 KB

    The zebra stripes on the knees are from a kneeling pad that has alternating yellow and black. Apparently the black is deteriorating. The sweat is all mine.

    Now that the temporary V struts are in place we can fit the landing wires. They should be here Thursday with factory forks on one end.

    Dale
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  3. #193

    Join Date
    Aug 2011
    Location
    Alabama
    Posts
    2,002
    That's the nice thing about practicing on the rudder - it's easy to strip, clean and try again on.

    I did break down and buy actual Stewart's fabric glue, mostly because the 3M stuff Robert provided was pretty gummy by the time I cracked it open.

    Your seat elevation is spot on, but I suspect you'll wind up making the same mod to the push rod I did to keep it that low.
    The opinions and statements of this poster are largely based on facts and portray a possible version of the actual events.

  4. #194
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    193
    I received the fresh 3M Fastbond today. Hopefully I can try it in the next few days. I hope to do it in an air conditioned area so it's not so darn hot and humid. May make a difference.
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  5. #195

    Join Date
    Aug 2011
    Location
    Alabama
    Posts
    2,002
    What, you don't like painting a six inch long strip of glue to see that when the brush reaches the end, the front is dry?
    The opinions and statements of this poster are largely based on facts and portray a possible version of the actual events.

  6. #196
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    193
    Landing wires installed today.

    Name:  m_20180818_140709_1534622760651.jpg
Views: 24
Size:  52.9 KB Name:  m_20180818_140725_1534622729457.jpg
Views: 24
Size:  30.9 KB

    Name:  m_20180818_140734_1534622729347.jpg
Views: 25
Size:  40.9 KB Name:  m_20180818_140756_1534622654719.jpg
Views: 26
Size:  35.5 KB
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

  7. #197
    bookmaker's Avatar
    Join Date
    Nov 2011
    Location
    Florida Panhandle
    Posts
    193
    One half of the rudder is now covered.

    Name:  m_20180819_160516_1534712830993.jpg
Views: 14
Size:  33.2 KB Name:  m_20180819_160527_1534712830749.jpg
Views: 14
Size:  34.6 KB

    Unfortunately, when I opened the adhesive jug, I found it was neutral color rather than green that I thought I ordered. Previously while watching Shirley Girard working on Russ Turner's Camel wings with neutral Stewarts adhesive, she noted she was adding a little chalk line blue to give a little color so she could see where she was working. I found it to be very difficult as well.

    I am not sure if the SS adhesive is really different than the 3M (although several have posted that the advertised chemical make up is identical), I did have some issues:

    I could not get the fabric to stick to the "dried" adhesive as is done in the SS videos. I may not have applied enough glue. However, it does react to heat and sticks when heated.

    As noted above, the neutral is difficult to determine where you have glue and where you don't.

    There is a definite learning curve to do it neat and tidy. I do feel pretty good about the end results however. I will not try the other side until I have sufficient time to work with it and not feel pressured.

    Finally, I need to get a different iron. I tried two and the temps seem to be unstable. I did not shrink past the 250 degree setting. I think!

    Rose is going off for a few days, so I will not have a helper. I think I will wait until she gets back.
    Dale Cavin
    Florida Panhandle
    Current Project: Airdrome Aeroplanes Full Size Nieuport 17

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •