Results 1 to 10 of 10

Thread: Sonex/Jabiru 3300 Exhaust Question

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1

    Join Date
    Aug 2011
    Posts
    35

    Sonex/Jabiru 3300 Exhaust Question

    I have a Zenith CH750/Jabiru 3300 and the exhaust system is very leaky at the slip joints where the 3 headers on each side meet the muffler's sockets. The slip joints aren't the tightest and due to backpressure, most sealants burn/blow out. Compounding the problem is that there really isn't enough room on the muffler side of the joint to wrap, clamp, band, etc. any sort of overlapping material to attempt to seal the joint.

    Why's a CH750 owner asking a Sonex question?

    I understand that the usual Jabiru 3300 installation in a Sonex utilizes straight exhaust pipes rather than a muffler. Seems like that should provide very minimal back-pressure on the 3-into-1 collector. The muffler on the CH750 installation seems very restrictive and probably produces a lot of back-pressure. Are the Sonex's slip joints very leaky? Just wondering if reducing back-pressure on my 750's exhaust system would help cut down on leaks or help keep sealant in the slip joints!

    John
    N750A

  2. #2

    Join Date
    Jul 2011
    Location
    Tustin, CA
    Posts
    73
    I made that switch on my Texas Sport Cub with a Jabiru engine. The original big can-style muffler that came with the engine is a piece of junk. It leaked so badly that I removed the cabin heat valve for fear of killing myself with CO. I complained to Jabiru USA about it and they sent me a new muffler, but it was just as bad as the one I had.

    The Sonex-type collectors -- one on each side -- work much better and have a much better seal where the exhaust pipes enter the collector. It is not perfect by any means, but it is MUCH better. I think the engine makes a bit more power, too, although I have no way to actually verify that.

  3. #3

    Join Date
    Aug 2011
    Posts
    35
    I, too, am chasing high CO in the cockpit and believe most of it is coming from under the cowl from the leaky slip joints. I'm sealing the firewall as much as possible, but still want to eliminate the source!
    I found that one of my baffles was loose, so I'm having the muffler shell opened up to retrieve it and told the welder while he was at it, to go ahead and remove the other baffle. The 2" o.d. exhaust pipe crosses the interior of the muffler shell and is welded on both sides for support. I "think" it is just perforated with tiny holes as it crosses the interior of the muffler. I told him to cut big holes in the interior exhaust pipe to the point to just leave enough structure for support. This should reduce the backpressure in the muffler quite a bit.
    I'm then going to reinstall it with Wurth's Exhaust Sealant - good for 1300F and OEM to Porsche and apparently used on motorbike header/exhaust slip joints with success. Hard to find and expensive (by car standards, not aviation standards! HA!), but I figure the Wurth is worth (pun intended!) a shot! I'm going to use some "Tiger Patch" resin impregnated glass cloth (good for 1900F) secured with stainless wire ties to butt up against the gap between the header and the muffler inlet socket. Hopefully, this will "dam up" the sealant to help prevent blow-out. Better would be to wrap it around the joint on both sides, but as you know, the muffler sockets are right against each other and you can't get anything around the exterior of them.
    If all else fails, I may very well go the straight pipe route simply to get the lowest possible backpressure and have more exhaust go out the end of the pipe and not the slip-joint! I'd really prefer, however, to retain the muffler shell so as not to have to fabricate new cabin and carb heat systems.
    Last edited by jaustinmd; 03-07-2013 at 05:16 PM.

  4. #4
    Eric Witherspoon's Avatar
    Join Date
    Jul 2011
    Location
    Tucson, AZ
    Posts
    200
    I have the Sonex/3300 3-into-1 outlets. I wouldn't be surprised if they are using the exact same tubing combination of OD x wall as on the muffler you're having trouble with, because they fit really loose and leak like crazy. I tried wrap, but you know what? If you don't stop the FLOW, wrap just gets blown through and burned up (something about that 1300-1400F exhaust gas). I believe wrap can truly insulate to the SURFACE temp of an exhaust pipe, but when there's flow, wrap is hopeless. It just turns to charred ash and falls away, and you're back where you started. So you have to stop the flow.

    Someone on the Sonex group mentioned chimney cement - not sure how much jaustin's Wurth's stuff is, but chimney cement is about $3 for a little tub at the local airplane supply (hardware) store - enough to do 100 airplanes' worth of exhausts. But the little tub will dry up and turn into a brick-in-a-can before you can re-apply it next year... It's a ceramic product, which means it's crumbly, and will probably just turn to dust and fall out of the joint after a while. But it's cheap, easy to apply, and does seal the pipes.

    Any comments about "reducing the back pressure" - well, that's like putting your thumb in the dam. Say you reduce the back pressure by 2psi, when there's 100 psi coming out, how much flow did you reduce? If there's leaks in the joint, it's gonna leak (big) under the cowling regardless of whether you have 10" or 3 feet of tube between the leak and the outlet. Stop the flow is the name of the game.

    Practically, though, for how short the Sonex 3-to-1 outlets are, I wonder why they are separate parts, other than to make the engine easier to fit into their shipping crate. Anybody just weld it all up and be done with it? The old "log" style headers used to be that way - just 1 all-welded collection of tubes per side. Here's some photos I took of the factory Sonex/3300 back in 2000. Exhaust = 1 piece per side, so it can and has been done.
    Name:  sonexe3.jpg
Views: 2614
Size:  19.9 KB
    Name:  sonexe2.jpg
Views: 3317
Size:  18.2 KB

    Name:  sonexe1.jpg
Views: 3128
Size:  24.4 KB
    Murphy's 13th: Every solution breeds new problems...

    http://www.spoonworld.com

  5. #5

    Join Date
    Aug 2011
    Posts
    35
    Eric - Stopping flow through the slip joint is exactly what I'm trying to do! The Wurth's is to seal the joint (stop flow or blow back) - the wrap is merely to help hold the sealant in place, not to seal off the flow. We're talking the same ideas, just different materials.

    HOWEVER, I think you're underestimating how much backpressure reduction is possible. I've found one guy with a 3300's headers just jammed into a single collector (no slip joints) that tapers to a straight pipe. He really has less blow-back than a stock system through slip joints into a restrictive muffler. That's why I'm gutting the muffler to reduce back pressure on the slip joints.

    By the way, the Wurth's sealant is about $17 for 140 gms - enough to do several systems. The catch is that it's mostly available at foreign car aftermarket sources such as Pelican Parts - so you have to pay a few bucks shipping. Supposedly, it's superior to the chimney cement, Permatex, etc., but maybe that's because one paid so much for it!
    Last edited by jaustinmd; 03-09-2013 at 07:23 AM.

  6. #6

    Join Date
    Nov 2011
    Location
    Mt. Carroll, Illinois
    Posts
    3
    I've not had issues yet, but am getting a CO meter to check the situation. I did just notice that I've got a lot of rust on the bottom of my muffler? I'm thinking that the weather here in northern Illinois has been so humid and cold that the problem is greater than norm? Anyone else have the problem?

  7. #7
    sonex293's Avatar
    Join Date
    Jul 2011
    Location
    Cary, NC
    Posts
    26
    Yes, the Sonex exhaust is also "leaky" at those seams. I've got mine wrapped with and it helps control the leak, but doesn't prevent the leak. I have to replace the wrap every year at annual time. Someone on the Yahoo! SonexTalk forum created a custom tool to add a "bead" on one end and he claims it really helped control the leaks. We'll see after he's flown with it for a year!

    ==
    Michael
    Sonex N293SX

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •