Search:

Type: Posts; User: Eric Brown

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    418

    Here's a late thought. Has anyone had experience...

    Here's a late thought. Has anyone had experience with the Marvel carb. one piece venturi and the type of fuel nozzle used. My carb. is a 10-4894 that has the one piece venturi mod, but retained the...
  2. Replies
    4
    Views
    418

    I guess my hopes were to great. The RPM problem...

    I guess my hopes were to great. The RPM problem still exists. I had lots of time to evaluate on recent 2 hr flight. It still turns only 2350 RPM during climb and only 2500 in level flight after the...
  3. Replies
    4
    Views
    418

    Well Ron, you were close. When I wrote this...

    Well Ron, you were close. When I wrote this thread, I had not performed any investigation as it was the end of the day. It appears that I cried "mystery of the month" too soon.
    What I found today...
  4. Replies
    4
    Views
    1,777

    The used actuator works properly. There is no p/n...

    The used actuator works properly. There is no p/n on the units to ID these things. You have to measure the jackscrew or the microswitch bar.
  5. Replies
    4
    Views
    418

    Engine performance mystery

    I have a Cessna 150L with a newly overhauled O-200 engine. The engine has been flown twice. On the second flight I noticed that the RPM, during climb, was only 2300 RPM. The engine ground static run...
  6. Replies
    5
    Views
    1,592

    Well guys ..... I'm working with an ASI at my...

    Well guys ..... I'm working with an ASI at my local FSDO. When he calls the registration branch, he admits that they are a little confusing. The ASI is recommending that I prepare a repair scheme,...
  7. Replies
    5
    Views
    1,592

    I believe chapter 4 often deals with damage...

    I believe chapter 4 often deals with damage caused by an accident in which an FAA or NTSB investigator would determine the airplane condition. This airplane was damaged on tie down by a windstorm...
  8. Replies
    5
    Views
    1,592

    Re-registration challenge

    This story starts in Nov 2017. I purchased a damaged C150L that had been de-registered. I didn't know it at the time, but the de-registration was because it was listed as "scrapped/destroyed". I...
  9. Replies
    4
    Views
    1,777

    Well ..... I finally was able to talk to Cessna...

    Well ..... I finally was able to talk to Cessna tech support. He could not give me an answer to exposure length of the jack screw. The only thing he could confirm is that Cessna installed a...
  10. Replies
    4
    Views
    1,777

    Cessna 150 flap travel

    Does anyone have knowledge of the physical differences in the Cessna 40 degree and 30 degree flap actuator assemblies ? The used assembly that I installed in my C150L has only enough travel to put...
  11. Thread: CorrosionX

    by Eric Brown
    Replies
    8
    Views
    2,202

    My home made spray devise is a hand held fire...

    My home made spray devise is a hand held fire extinguisher bottle with an inner tube filler valve installed on it for compressed air charging. The wand is a 6 ft long 3/16" brake line with small...
  12. Replies
    3
    Views
    1,925

    It is also considered to be a non-structural...

    It is also considered to be a non-structural rivet.
  13. Thread: CorrosionX

    by Eric Brown
    Replies
    8
    Views
    2,202

    Interestingly enough, that's exactly what I did. ...

    Interestingly enough, that's exactly what I did. Mixed it at 1/4 alcohol. Still a little thick, but seemed to permeate out.
  14. Thread: CorrosionX

    by Eric Brown
    Replies
    8
    Views
    2,202

    I'm using a home made long wand set up. The spray...

    I'm using a home made long wand set up. The spray nozzle isn't the most efficient. It disperses water just fine, but the X is a bit thicker. Need to thin it down to water viscosity.
  15. Thread: CorrosionX

    by Eric Brown
    Replies
    8
    Views
    2,202

    CorrosionX

    Has anyone out there tried to thin out CorrosionX for better spraying and atomizing ? What could you use that would not degrade the effectiveness of the CorrosionX ?
  16. Ya know ...... I had to go back and read 91.225....

    Ya know ...... I had to go back and read 91.225. It's interesting. Para.(e)'s first sentence seems to grant a blanket exclusion to non-electric system airplanes. Then the second sentence takes that...
  17. I don't quite understand your stated problem...

    I don't quite understand your stated problem concerning having only 2 choices to either sell or move your airplane. How about removing the transponder /encoder/ ADS-B and using the battery only for...
  18. Replies
    10
    Views
    15,103

    Ya know what ?? I found Cole T. Wagner. He's...

    Ya know what ?? I found Cole T. Wagner. He's still selling STCs and Aeronca parts. 605-532-3862.
  19. Replies
    10
    Views
    15,103

    In these last few years ........... has anybody...

    In these last few years ........... has anybody been able to locate a source for the Wagner STC SA3-372 ?????
  20. Replies
    7
    Views
    2,892

    Certified to EAB.

    Gentlemen;
    I am planning to take a 7AC Champ that is currently in many pieces, that is de-registered (not scrapped or destroyed) and rebuild it with my mods and certify it as a light sport EAB. ...
  21. Replies
    2
    Views
    3,437

    Thought possibly it may not be Cessna, but in my...

    Thought possibly it may not be Cessna, but in my 50 yrs of working on GA aircraft, I only recognize it as Cessna. Photos attached.
  22. Replies
    2
    Views
    3,437

    Cessna trim actuator

    I am trying to identify the part number of a Cessna trim actuator. Externally it looks identical to the Cessna 100 series elevator trim actuators, however it's has a steel case and the end bearings...
  23. Replies
    7
    Views
    3,441

    Ya know, you could try a little deal that Piper...

    Ya know, you could try a little deal that Piper used to install their Tomahawk trainers. It was a heat sink finned can that slid over the oil filter and had an air blast hose nipple on it to connect...
  24. Replies
    7
    Views
    12,730

    I commented to your 4-18-2020 post. The C150B did...

    I commented to your 4-18-2020 post. The C150B did not have the skylight option which made a field approval necessary. The C150M has the option. Go for it !!
  25. Replies
    7
    Views
    4,493

    No FAA field approval or STC is needed for this...

    No FAA field approval or STC is needed for this installation. Check your airplane's approved equipment list. It should list the skylight windows as a piece of optional equipment. If it's on the...
Results 1 to 25 of 118
Page 1 of 5 1 2 3 4